Skip to content
Serving San Jose and nearby cities Mon–Fri: 8 AM–8 PM · Requests accepted 24/7 · (669) 201-9530

Furnace Repair in Fremont, CA

The short answer

EliteAir repairs gas furnaces in Fremont, including ignition, flame sensing, inducer, blower and venting problems. Each visit includes a carbon monoxide and safety check, and you approve the repair before work begins.

Fremont winters are cool and damp rather than harsh, yet the furnace still carries a real load from late fall into early spring, especially in the morning hours and in homes on the hillier eastern side of town. When it fails, the house turns chilly fast. EliteAir repairs gas furnaces throughout 94536, 94538, 94539 and 94555, driving about twelve miles north from San Jose into Alameda County. We handle furnaces in garages, hall closets, attics and crawlspaces, from older standard-efficiency units to modern condensing models. This page explains how to read the warning signs, what you can safely check on your own, how we troubleshoot, and how to think about an older furnace now that the Bay Area rules for gas appliances are changing.

Warning signs worth acting on

A furnace usually gives some notice before it quits. Paying attention to these early signs can turn an emergency into a scheduled repair.

  • Several attempts to light before the burners finally catch
  • Burners that light, then go out after a short time
  • Air from the vents that never gets properly warm
  • A blower that will not shut off, or that never starts
  • New noises: squealing from the blower, rattling from the inducer, a loud bang at ignition
  • Yellow or flickering flames where they should be steady and blue
  • A status light on the control board blinking a repeating pattern

What you can check, and what to leave alone

Start with the simple items. Make sure the thermostat is in heat mode, set above the current room temperature, and has fresh batteries. Replace the filter if it is dirty. Confirm the furnace power switch, which often looks like a light switch on or near the unit, is on, and that the front access panel is fully seated; many furnaces will not run with the panel off because of a safety switch. Check the breaker panel for a tripped furnace circuit.

Leave the gas valve, burners, igniter and safety switches alone. If you smell gas, get everyone outside, avoid using switches, and call your gas utility from a safe distance. If your carbon monoxide alarm goes off, leave the house and call emergency services. Those situations come before any HVAC repair.

How we troubleshoot a furnace

We read any stored fault codes, then watch a full heating cycle from the thermostat call through ignition and blower startup. Seeing where the sequence stops tells us which component to test. We use meters to verify the inducer motor, pressure switch, igniter, gas valve, flame sensor, limit switches and blower before replacing anything.

On condensing furnaces, which are common in remodeled Fremont homes, we also check the condensate trap and drain, since a blockage there often causes the furnace to start and then shut down repeatedly. Before leaving, we measure temperature rise, check gas pressure, look over the visible heat exchanger and venting, and test for carbon monoxide. If we find an unsafe condition, we explain it and shut off the gas to the appliance until it is corrected.

Older furnaces and changing rules

Some Fremont homes still have their original furnaces. Many can be kept running for a while with good repairs, but at some point parts become hard to find or the heat exchanger shows wear. When we reach that point, we tell you directly and give you both paths.

Fremont is covered by the Bay Area Air District. Under Rule 9-4, natural gas furnaces manufactured from 2029 must meet a zero-NOx emission standard, which in practice points homeowners toward heat pumps when a furnace is replaced after that date. The rules do not force anyone to remove working equipment; they only apply when a furnace fails or is replaced. If you are curious about a heat pump, BayREN and your local clean energy provider may offer incentives, and we confirm the current offer before including it in a quote.

We also repair furnaces in Milpitas, Sunnyvale, Santa Clara, Mountain View and Los Altos.

More services in Fremont

Related

What to expect

How a visit goes

  1. Measure first

    Temperatures, pressures, electrical readings and airflow come before any recommendation, so the fix addresses the actual fault.

  2. Show and explain

    We point out failed parts or readings, describe what they mean, and answer questions until the choice makes sense to you.

  3. Respect the home

    Floor protection, careful attic and closet work, and a cleaned-up space before we leave are standard on every visit.

FAQ

Common questions

Don’t see your question? Call (669) 201-9530 and we’ll talk it through.

Why does my furnace try to light several times?

Repeated ignition attempts often come from a weak igniter, a dirty flame sensor or low gas pressure. We test each to find the cause.

Is a yellow flame dangerous?

It can indicate incomplete combustion. Turn the furnace off and have it checked, including a carbon monoxide test.

My furnace is in the crawlspace. Can you work on it?

Yes. We repair furnaces in crawlspaces, attics, closets and garages, and we check access, venting and wiring in each location.

What does the blinking light on my furnace mean?

It is a diagnostic code. Count the blinks and check the chart on the furnace door, or tell us the pattern when you call.

Do I have to replace my gas furnace because of Air District rules?

No. The rules apply when a furnace fails or is replaced. A working furnace can remain in service.

Tell us what your system is doing

Describe the symptom and where the equipment is, and we will schedule a visit, diagnose the problem and walk you through your options.

Request Service Call (669) 201-9530
Call (669) 201-9530 Request Service